I hate to lower the level of intelligence here but is it ok to use a
GT45 with a holley carb draw through style . The fuel itself would help
cool things down wouldn't it?
Any intake manifold pressure relief would have to be exited to the
outside of the cowl or perhaps back into the end of the exhaust .
Wastegate alternative as described by you Paul could still be the same.
My other thought was towards the propeller. Is there a propeller that
could take 350hp and be ground adjustable to soak up 650 hp at a latter
date?
Hope I am not to far off the planet. Its all new stuff to me
Mark Dillner
I built a 3 rotor version but so far I did not run it. So I have no
experience.
Here are a few pictures. I'll sell the carb if you want to buy it.
Paul Lamar
I think it's way to early for me to be buying those parts yet Paul.
I started thinking if I could have a reliable 350 hp it would pull my
BD4 upwards ,as they say, like a homesick angel and if then with an even
larger Holley or maybe just opening the secondary's the cfm would be
large enough to pull double that.
However, the length, pitch or number of blades required to soak up the
power may be way past my pocket savings.
That is the great thing about the Mazda. It has the reserve capacity to
upgrade way past what is normally possible with any reliability so I
shall stick with it. No other engine is going to give me the flexibility
or reliability of the rotary.
That's why I figure I should start with large turbo ,large Holley four
barrel so it can perhaps be used as a two barrel until time comes to up
the HP and prop size.
You did say what prop is used on the TTC and maybe I should watch out
time to time for something in that range to pop up .
As I said it's new to me but I have made parts before . I used to
rebuild MGB's into a Sebring style and I made my own gas (lpg)
carburettor and suspension parts for my 65 Mustang 302 so I can nut a
few things out.
Mark Dillner
I think my Holley is 750 CFM.
I used to have a Sprite a long time ago. The most amazing things broke.
How about a cracked rear brake cylinder :-)
I did an XKE hood for it.
Paul Lamar
FI Tech makes a self contained throttle body system that is blow through
capable up to 25 psi. Other than a swap of the 4150 style carb, it
requires an O2 sensor bung in the exhaust for the Bosch wide band sensor
to be closed loop. Comes with a small tablet to adjust the ECU which is
built in to the throttle body.
Can't say anything first hand about it. A friend of mine installed one
of the FI Tech units on a Chevy small block with good results. It
impressed me because it is probably the simplest carb to EFI setups out
there. IIRC
Atkins sells a 4150 manifold for the 13B. I plan to buy one of the NA
style for my Ford 400. They also have a sump style canister (they call
it fuel command center) to simplify plumbing the high fuel pressure needed.
Basically a lower pressure fuel pump can supply the sump and the sump
relays high pressure fuel to the throttle body and the excess from the
regulator is routed back to the fuel command center, eliminating the
need for a fuel return to the main tank.
NA part number: FIF-30003 (4 ea. 55 lb./hr injectors: 400hp) 795.00 USD
Boost part number: FIF-30004 (unspecified injectors: 600hp) 1195.00 USD
Alan Mullen
That is way too much for injectors. The four Bosch 2000 we used on the
650 HP TTC were less
than $500.
Paul Lamar
The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove you. ACRE NL web
site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.