Subject: Turbo Rx8 carb draw through style
From: paul lamar
Date: 6/17/2017, 3:08 PM
To: A10-Me-Earthlink


    I hate to lower the level of intelligence here but is it ok to use a
    GT45 with a holley carb draw through style . The fuel itself would help
    cool things down wouldn't it?

    Any intake manifold pressure relief would have to be exited to the
    outside of the cowl or perhaps back into the end of the exhaust .
    Wastegate alternative as described by you Paul could still be the same.

    My other thought was towards the propeller. Is there a propeller that
    could take 350hp and be ground adjustable to soak up 650 hp at a latter
    date?

    Hope I am not to far off the planet. Its all new stuff to me

    Mark Dillner


      I built a 3 rotor version but so far I did not run it. So I have no
    experience.
    Here are a few pictures. I'll sell the carb if you want to buy it.


    Paul Lamar


    I think it's way to early for me to be buying those parts yet Paul.
    I started thinking if I could have a reliable 350 hp it would pull my
    BD4 upwards ,as they say, like a homesick angel and if then with an
even
    larger Holley or maybe just opening the secondary's the cfm would be
    large enough to pull double that.
    However, the length, pitch or number of blades required to soak up the
    power may be way past my pocket savings.


    That is the great thing about the Mazda. It has the reserve capacity to
    upgrade way past what is normally possible with any reliability so I
    shall stick with it. No other engine is going to give me the
flexibility
    or reliability of the rotary.


    That's why I figure I should start with large turbo ,large Holley four
    barrel so it can perhaps be used as a two barrel until time comes to up
    the HP and prop size.
    You did say what prop is used on the TTC and maybe I should watch out
    time to time for something in that range to pop up .
    As I said it's new to me but I have made parts before . I used to
    rebuild MGB's into a Sebring style and I made my own gas (lpg)
    carburettor and suspension parts  for my 65 Mustang 302 so  I can nut a
    few things out.

    Mark Dillner

    I think my Holley is 750 CFM.

    I used to have a Sprite a long time ago. The most amazing things broke.
    How about a cracked rear brake cylinder :-)

    I did an XKE hood for it.

    Paul Lamar

    FI Tech makes a self contained throttle body system that is blow
through capable up to 25 psi. Other than a swap of the 4150 style carb,
it requires an O2 sensor bung in the exhaust for the Bosch wide band
sensor to be closed loop. Comes with a small tablet to adjust the ECU
which is built in to the throttle body.

    Can't say anything first hand about it. A friend of mine installed
one of the FI Tech units on a Chevy small block with good results. It
impressed me because it is probably the simplest carb to EFI setups out
there. IIRC

    Atkins sells a 4150 manifold for the 13B. I plan to buy one of the
NA style for my Ford 400. They also have a sump style canister (they
call it fuel command center) to simplify plumbing the high fuel pressure
needed.

    Basically a lower pressure fuel pump can supply the sump and the
sump relays high pressure fuel to the throttle body and the excess from
the regulator is routed back to the fuel command center, eliminating the
need for a fuel return to the main tank.

    NA part number: FIF-30003  (4 ea. 55 lb./hr injectors: 400hp)
795.00 USD
    Boost part number: FIF-30004 (unspecified injectors: 600hp) 1195.00 USD

    Alan Mullen

    That is way too much for injectors. The four Bosch 2000 we used on
the 650 HP TTC were less
    than $500.

    Paul Lamar

Mark, if you want to use draw through use a wastegate. Talk to Garret
for the turbo housing A/R's, turbo model for what you are doing and the
engine. Same goes for the wastegate. May be wise to have two, one set
for 0.5 PSI higher boost pressure in the case the main one cannot
maintain the boost control. Better than dumping fuel.

Dale Davies

You don't need a waste gate for an aircraft engine. Just use a manifold
blow off valve set to the max boost
you want.

A waste gate is designed to allow the turbo to spin up fast. Not needed
in an aircraft engine.

Paul Lamar

Thanks to all of you for input.  Almost gone full circle back to EFI as
big carbs start to weigh big time and this nose weight control is
crucial to good handling it seems. I am trying to fight it but it does
make sense.

Thing is I am  still  don't know all the things my phone can do or what
the TV clicker thingy is capable of. It just doesn't interest me . I
love old mechanical. It's simple and understandable. I used to get up
and push a button on the telly to turn it off or on or to change
channels and it didn't do me any harm. The only surfing we did in those
days was in the ocean.

As for my phone, I just want it to take or receive calls and txts. I
know what they can do with an "APP".

Crickey I am supposed to be improving my knowledge and articulation of
the French language but there is no room left up top with thoughts of
motor and airplane bits. Will have to continue with the pointing of the
finger and grunting method.

Can't fathom how a brake cylinder cracked Paul. Must have been a faulty
cast. We all have our gritting of teeth moments with Lucas electronics.

Sprite would be supper smart with an xke style bonnet.

Mark Dillner

Trust me and look into a Maximate. There was a company in the UK selling
them to children. A closed loop EFI software is trivial. One page.

Or if you find a company selling EFI ask them if it is closed loop with
a Bosch O2 sensor. Could be a French company :-)

BTW what town do you fly into in the south of France?


Paul Lamar

I shall follow that up thanks Paul.

I don't fly. I don't have a license. I always figured when I had my own plane I would get a license. Might have left it too late now but I am enjoying finally having some aircraft projects. I did solo in a Tomahawk during my time living in Perth WA in the 80's. That followed by going solo in a microlight here in the UK mid 90's convinced me not to go further until or if I got my own aircraft.

My small apartment in Provence is two villages towards the sea from the gliding center at Fayence and my little house is in the middle of France. Nearest small airfield is Moulins or Nevers

Mark Dillner

I got my license in a Tomahawk. Nice little  air plane.

I love Perth too. Great city. The weather is the same as LA.

We have/had  several people out at Serpentine airport building rotary powered
airplanes.

We also went up to Bindoon north of Perth.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net <http://www.rotaryeng.net/>You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.