Subject: Making your own steel coupling.
From: paul lamar
Date: 6/21/2017, 6:53 PM
To: A10-Me-Earthlink



    I have an idea for you Scott.

    There is a water jet company in 1500 Airway Circle, New Smyrna Beach
    FL. 32168 | 386-424-7333 <tel:386-424-7333>

    http://www.advmach.com/waterjetcutting.html <http://www.advmach.com/waterjetcutting.html>

    I have some drawings of a steel coupling that can be made out of
    water jet cut steel parts.

    Then you will need to find a local tig welder to weld it up.

    I have some of the parts. The inner plate that bolts to the counter
    weight and the outer ring cut from six inch tubing.

    $50 plus mailing.

    Use part of Tracy's torque isolator to adapt this to Tracy's PSRU
    input shaft. Drill out the rivets and bolt it to the steel output
    front plate.

    Paul Lamar




    Very interesting!  I can query the water jet shop, and will order
    these parts if the  shop can make the rest.  No problem with the
    welder.

    How thick is the metal?

    Do you intend for an outer ring to be cut into the small curved
    shapes, or make these from scratch?  I guess  they can be flat
    instead of curved?

    I also assume the 1.78” is the height of each component, so the total
    thickness would be about 2”?  I will study my redrive to look for
    areas of potential interference.

    Please ignore the curved questions of my last post, sorry. Some of
    the latter images didn’t display the first time.  I see the
    connecting elements are square.

    Thanks!

    Scott Gettings

    .050 to .150. Some of the stuff is  .083. You make it out of what you
    can find :-) The six inch tubing is about .150 wall.

    The total thickness is about 1.8 inches. Nothing about this is
    critical. One inches would work if your not shooting for 500 HP.

    Ignore those square pictures. The latest are triangular or wedge
    shaped. The square ones bottom out corner to corner. We discovered
    that when we built the TTC coupling.

    If I get a little more interest in this I wall make a tool that bends
    the wedges in a hydraulic press. Saves a bit of welding. I have built
    tools like that in the past. That would pay off as the same design
    can be used in new gear boxes. We already used one of these that was
    similar in a 3 rotor.

    I have not heard back from Kevin so if Kevin finds an NC shop that
    can make them out of billet at reasonable cost that would be more
    accurate.

    In any event once this is welded up it would be wise to balance it
    between parallel bars. If your gear box is off the engine please tell
    me the diameter of the input spline adapter Tracy is using. The one
    with all the rivets. That will control the diameter of the forward
    plate.

    Paul Lamar



   Paul,

   My welder can assemble these small steel parts, but is not highly confident of the  precise alignment and balance of the end product. It looks like some other options are evolving, so I’ll keep  this one on hold.

   My gearbox is on the engine, but if you need the exact shaft diameter soon, I will be happy to pull the it and measure the shaft.

   Other measurements that might be helpful:
   distance from front edge of flex plate gear to rear of engine block:  1 5/16”
   distance from front of Tracy’s adapter plate to engine block (the total “open” area between the engine and adapter):  3 1/8”
   distance from front of Tracy’s adapter plate to rear face of his riveted spline adapter:   1 1/4”
   the front of the spline adapter appears very close to the rear edge of the flex plate ring gear.

   It appears that the total thickness of a new coupler (for Tracy’s RD) would need to be the exact distance from the rear face of the bolted area of the flex plate to the rear of its ring gear, which is the plane of the front of the riveted part of the spline adapter. This would maintain the dimensions for the thrust bearings.  A coupler that is more thick than this would move the rest of the RD to the rear, requiring alteration of the existing spacers (the 3 1/8” distance).  A thinner coupler could be managed with thrust bearing washers.

   Scott Gettings

   I just happened to have one.
   The OD of the part in question is 6.188. The long part that sticks away from
   the engine 1.158 long.

   The idea is to turn it around and put the long part inside the coupling.
   We worked this out years ago :-) 3D's 5 and six show this config.

   That Ford part raw weighs 3 pounds. There is unnecessary meat on
   both sides that I can be cut off if you send me yours. That will give you
   plenty of room and save a bit of weight. Some of the spline part can be
   cut off as well. 1.25 inches of spline would be plenty.

   Jean is down the road from you in Pompano Beach and he might do
   it for you. He has a lathe and a mill. He will need one sooner or later :-)

   Here are a few pictures.

   Paul Lamar

Paul how is the reliability on the auto trans style planetary type psru like you guys are running, are there a few out there with some time on them? I would think it's better than the gear and idler set up there running on ls1 motors and stuff. It's not a problem cause the rotary engine profile is so small but for a v8 or something unless it was inverted the crank center line is probably too low for most airframes. Most auto conversions seem to have a lot of gearbox problems, the design you guys are using seems pretty solid. Have you seen anyone make one with a constant speed hub?

Thanks, Jacob Sturges

Been used since 1973. Ford has beefed it up over the years. Started with
3 pinions now up to six. Used on the Power Stroke diesel in heavy duty
pick up trucks.
Paul how is the reliability on the auto trans style planetary type psru like you guys are running, are there a few out there with some time on them? I would think it's better than the gear and idler set up there running on ls1 motors and stuff. It's not a problem cause the rotary engine profile is so small but for a v8 or something unless it was inverted the crank center line is probably too low for most airframes. Most auto conversions seem to have a lot of gearbox problems, the design you guys are using seems pretty solid. Have you seen anyone make one with a constant speed hub?

Thanks, Jacob Sturges

I would say well over a hundred have flown with another 100 in the works.
One guy on a gyro had over 2600 hours in flight training service.
Many people have well over 1000 hours.

Paul Lamar

   The Rotary Engine free News Letter. Powered by Linux. If you want off
   the list PLEASE let me know and I will remove  you.  ACRE NL web
   site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2017 All world wide rights reserved.