Subject: Water Jet aluminum couplings
From: paul lamar
Date: 6/30/2017, 7:08 PM
To: A10-Me-Earthlink




   My gearbox is on the engine, but if you need the exact shaft diameter
   soon, I will be happy to pull the it and measure the shaft.

   Other measurements that might be helpful:
   distance from front edge of flex plate gear to rear of engine block:  1
   5/16” distance from front of Tracy’s adapter plate to engine block (the total
   “open” area between the engine and adapter):  3 1/8”
   distance from front of Tracy’s adapter plate to rear face of his
   riveted spline adapter:   1 1/4”
   the front of the spline adapter appears very close to the rear edge of
   the flex plate ring gear.

   It appears that the total thickness of a new coupler (for Tracy’s RD)
   would need to be the exact distance from the rear face of the bolted
   area of the flex plate to the rear of its ring gear, which is the plane
   of the front of the riveted part of the spline adapter. This would
   maintain the dimensions for the thrust bearings.  A coupler that is
   more thick than this would move the rest of the RD to the rear, requiring
   alteration of the existing spacers (the 3 1/8” distance).  A thinner
   coupler could be managed with thrust bearing washers.

   Scott Gettings

   I just happened to have one.
   The OD of the part in question is 6.188. The long part that sticks away
   from the engine 1.158 long.

   The idea is to turn it around and put the long part inside the
   coupling. We worked this out years ago :-) 3D's 5 and six show this config.

   That steel Ford part raw weighs 3 pounds. There is unnecessary meat on
   both sides that I can  cut off if you send me yours. That will
   give you plenty of room and save a bit of weight. Some of the spline part can be
   cut off as well. 1.25 inches of spline would be plenty.

   Jean is down the road from you in Pompano Beach and he might do
   it for you. He has a lathe and a mill. He will need one sooner or
   later :-)

   Here are a few pictures.

   Paul Lamar

   Paul

   I revised the drawing and design the stencil template for
   waterjet cutter, see attached file for each of them plus
    the file as solid parts the back plate to suit the ford plate
   as 1.860 Dia where spline shaft attached.

   I will get one sample as soon i get the quotation from them.

   JEAN PRUDHOMME

   Use part of Tracy's torque isolator to adapt this to Tracy's PSRU
   input shaft. Drill out the rivets and bolt it to the steel output
   front plate.

   Paul Lamar

   Hi Paul

   Before leaving for Canada i did had time to pick up the
   watercutter parts for the coupling and it look very nice
   with a slight adjstment with filing edges.

   I will get it welded on my return.


   JEAN PRUDHOMME

   No doubt about it. This us the best way to build a coupler.
   Just cut silicon rubber blocks to fill the gaps.

   Paul Lamar


   I could have asked before, but this design has been evolving. Any guess as to what torque it will withstand, say from a 500HP 2 rotor.

   Steve Carlisle

I think you would have to do an FEA to have some idea of that.

What always amazes me is the e-shaft and the counter weight assembly
is taking two or three times the stock torque on the TTC. It must
be way over designed. The 4 rotor puts all of its torque through
the same place.

I'll be up in Seattle is a few days. How about a visit?

Paul Lamar

   The Rotary Engine free News Letter. Powered by Linux. If you want off
   the list PLEASE let me know and I will remove  you.  ACRE NL web
   site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2017 All world wide rights reserved.