Subject: EFI Maximite was EFI and CD ignition
From: paul lamar
Date: 9/7/2017, 7:22 AM
To: A10-Me-Earthlink


Paul,

I ordered 2 RX 8 crank angle sensors and am fabricating a bracket to
mount the sensors.

Room is tight due to modified water pump and heat shield for the
augmenter.

Could you explain how the Mighty Mite will use the pulse generated by
the sensors and the one tit trigger wheel?

The first pulse would be firing ignition by the CDI and the MM would
know 20 degrees BTDC,

Does it look for the second pulse to get a time frame for one rev of
the Eshaft?

What happens next?

What would the code look like?

Thanks

Joe Berki

There is no code for the CD ignition. The maximite does not need to
be involved.

The front rotor (car) fires from the first CAS at 22 degree BTDC.
Then the second CAS 180 degrees later fires the rear rotor. That is
all there is to it.

That reminds me I need to check and see if I got the sample
transformer for the CD system.

Now the CAS can also be connected to the Maximite to fire the
injectors after it checks the mass airflow sensor and figures out the
correct pulse width.

Paul Lamar

This part is what I was trying to  understand I know the CDI is independent.

I wanted to know how the Maximite fires the injectors.

Joe Berki


The  Maximite has 20 I/O pins numbered 1 to 20,
All of these pins can be configured as digital out puts or something else.
The pin will put out 5 volts.

You choose the pin you want to control the injector.

Then it must first be configured.
The instruction is "SETPIN pin, cfg"
"pin" is simple the pin number you choose.
Let say you choose pin number 2

The instruction is then written SETPIN 2

cfg stands for configure.
Here is a list of possible configurations for most pins.

0 Not configured or inactive
1 Analog input (pins 1 to 10)
2 Digital input (all pins and 5V tolerant on pins 11 to 20)
3 Frequency input
4 Period input
(pins 11 to 14)
(pins 11 to 14)
5 Counting input
(pins 11 to 14)
6 Interrupt on low to high input change (pins 1 to 20, D0 to D8) for target
7 Interrupt on high to low input change (pins 1 to 20, D0 to D8) for target
8 Digital output  (all pins)
9 Open collector digital output to 5V (pins 11 to 20, D0 to D13) In this mode the
function PIN() will also return the output value.

We want to make it and out put pin so we choose # 8

The instruction is then written like this SETPIN 2, 8

That is all  we have to do to configure pin #2 as an output pin.
From now on it is an output pin.

Now when we tell pin to go high the injector will be fired.

PIN(2) = high   turns the injector pulse on 5V
We wait.  The wait time is a function of the mass airflow sensor.
PIN(2) = zero  turn the injector pin off.

That's it.

You have to get a Maximite and play with it.
You can use a volt meter to check your program.
Programming is mostly trying things and see if it does what
you want it to do.


Paul Lamar

Paul,

The hardware is the easy part I wanted to know where to start with the software after the pins are configured.
The 2 RX 8 sensors wil deliver a pulse when the CDI fires for both rotors.
The Maximite looks at this and will fire the injector and keep it on based on the MAF sensor voltage.
What computations need to take place to determine when to fire the injector based on ignition data?
The pulses and the time between the first pulse and the second pulse will give unit time per revolution.
The injection would be based on an event that already occurred.
Does the rear rotor pulse drive the front rotor Maximize for injection?

Joe Berki

Do you have a Maximite yet?

I had a brilliant idea yesterday to drastically simplify the code.

You use a FOR NEXT loop to time the injection,

The code would then look like this.

PIN(2) = high   turns the injector pulse on 5V when the CAS occurs.
FOR y = 1 to xxxx
  NEXT
PIN(2) = zero  turn the injector pin off.

xxxx becomes proportional to the mass air flow reading.

That's it !!!!!!
Your done !!!!!!!

One Maximite per rotor.

If I could only get a patent on this ROFL

Paul Lamar

Joe, the fuel system is independent from ignition. It starts up as soon as the mass airflow senses the cranking sequence.

Steve Carlisle

Google FOR NEXT LOOPs.

There is at least a half dozen explanations.
I was amazed.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.