Subject: EFI Maximite was EFI and CD ignition
From: paul lamar
Date: 9/7/2017, 10:11 AM
To: A10-Me-Earthlink


   Paul,

   I ordered 2 RX 8 crank angle sensors and am fabricating a bracket to
   mount the sensors.

   Room is tight due to modified water pump and heat shield for the
   augmenter.

   Could you explain how the Mighty Mite will use the pulse generated by
   the sensors and the one tit trigger wheel?

   The first pulse would be firing ignition by the CDI and the MM would
   know 20 degrees BTDC,

   Does it look for the second pulse to get a time frame for one rev of
   the Eshaft?

   What happens next?

   What would the code look like?

   Thanks

   Joe Berki

   There is no code for the CD ignition. The maximite does not need to
   be involved.

   The front rotor (car) fires from the first CAS at 22 degree BTDC.
   Then the second CAS 180 degrees later fires the rear rotor. That is
   all there is to it.

   That reminds me I need to check and see if I got the sample
   transformer for the CD system.

   Now the CAS can also be connected to the Maximite to fire the
   injectors after it checks the mass airflow sensor and figures out the
   correct pulse width.

   Paul Lamar

   This part is what I was trying to  understand I know the CDI is independent.

   I wanted to know how the Maximite fires the injectors.

   Joe Berki


   The  Maximite has 20 I/O pins numbered 1 to 20,
   All of these pins can be configured as digital out puts or something else.
   The pin will put out 5 volts.

   You choose the pin you want to control the injector.

   Then it must first be configured.
   The instruction is "SETPIN pin, cfg"
   "pin" is simple the pin number you choose.
   Let say you choose pin number 2

   The instruction is then written SETPIN 2

   cfg stands for configure.
   Here is a list of possible configurations for most pins.

   0 Not configured or inactive
   1 Analog input (pins 1 to 10)
   2 Digital input (all pins and 5V tolerant on pins 11 to 20)
   3 Frequency input
   4 Period input
   (pins 11 to 14)
   (pins 11 to 14)
   5 Counting input
   (pins 11 to 14)
   6 Interrupt on low to high input change (pins 1 to 20, D0 to D8) for target
   7 Interrupt on high to low input change (pins 1 to 20, D0 to D8) for target
   8 Digital output  (all pins)
   9 Open collector digital output to 5V (pins 11 to 20, D0 to D13) In this
   mode the
   function PIN() will also return the output value.

   We want to make it and out put pin so we choose # 8

   The instruction is then written like this SETPIN 2, 8

   That is all  we have to do to configure pin #2 as an output pin.
   > From now on it is an output pin.

   Now when we tell pin to go high the injector will be fired.

   PIN(2) = high   turns the injector pulse on 5V
   We wait.  The wait time is a function of the mass airflow sensor.
   PIN(2) = zero  turn the injector pin off.

   That's it.

   You have to get a Maximite and play with it.
   You can use a volt meter to check your program.
   Programming is mostly trying things and see if it does what
   you want it to do.


   Paul Lamar

   Paul,

   The hardware is the easy part I wanted to know where to start with the
   software after the pins are configured.
   The 2 RX 8 sensors wil deliver a pulse when the CDI fires for both rotors.
   The Maximite looks at this and will fire the injector and keep it on
   based on the MAF sensor voltage.
   What computations need to take place to determine when to fire the
   injector based on ignition data?
   The pulses and the time between the first pulse and the second pulse
   will give unit time per revolution.
   The injection would be based on an event that already occurred.
   Does the rear rotor pulse drive the front rotor Maximize for injection?

   Joe Berki

   Do you have a Maximite yet?

   I had a brilliant idea yesterday to drastically simplify the code.

   You use a FOR NEXT loop to time the injection,

   The code would then look like this.

   PIN(2) = high   turns the injector pulse on 5V when the CAS occurs.
   FOR y = 1 to xxxx
      NEXT
   PIN(2) = zero  turn the injector pin off.

   xxxx becomes proportional to the mass air flow reading.

   That's it !!!!!!
   Your done !!!!!!!

   One Maximite per rotor.

   If I could only get a patent on this ROFL

   Paul Lamar

   Joe, the fuel system is independent from ignition. It starts up as soon
   as the mass airflow senses the cranking sequence.

   Steve Carlisle

   Google FOR NEXT LOOPs.

   There is at least a half dozen explanations.
   I was amazed.

   ---------------------------------------------------------------

   One of the things you must do when converting the MAF sensor
   data to the required width of the pulse is know how much fuel
   will be injected for a given pulse width.

   I found a great site for calculation the size of the injector
   you will need.


   http://www.witchhunter.com/injectorcalc1.php <http://www.witchhunter.com/injectorcalc1.php>
   This screen capture  jpg shows that you will need 4 injectors

   420 cc/min to generate 250 HP full rich at a BSFC of .65 pounds of fuel per HP per
   hour. The RX8 yellow injectors alone won't handle it.

   You will need 41 pounds per hour from each injector.
   41 pounds is 6.56 gallons per injector.

   Now we need to have a chart for the injector chosen that shows the flow
   rate per millisecond of opening time. I am working on it.


   Paul Lamar

Paul, and more info from th guy that made the injector chart,
http://users.erols.com/srweiss

Steve Carlisle



   The Rotary Engine free News Letter. Powered by Linux. If you want off
   the list PLEASE let me know and I will remove  you.  ACRE NL web
   site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2017 All world wide rights reserved.