Subject: EFI Maximite was EFI and CD ignition
From: paul lamar
Date: 9/8/2017, 5:42 AM
To: A10-Me-Earthlink




    Paul,

    I ordered 2 RX 8 crank angle sensors and am fabricating a bracket to
    mount the sensors.

    Room is tight due to modified water pump and heat shield for the
    augmenter.

    Could you explain how the Mighty Mite will use the pulse generated by
    the sensors and the one tit trigger wheel?

    The first pulse would be firing ignition by the CDI and the MM would
    know 20 degrees BTDC,

    Does it look for the second pulse to get a time frame for one rev of
    the Eshaft?

    What happens next?

    What would the code look like?

    Thanks

    Joe Berki

    There is no code for the CD ignition. The maximite does not need to
    be involved.

    The front rotor (car) fires from the first CAS at 22 degree BTDC.
    Then the second CAS 180 degrees later fires the rear rotor. That is
    all there is to it.

    That reminds me I need to check and see if I got the sample
    transformer for the CD system.

    Now the CAS can also be connected to the Maximite to fire the
    injectors after it checks the mass airflow sensor and figures out the
    correct pulse width.

    Paul Lamar

    This part is what I was trying to  understand I know the CDI is
    independent.

    I wanted to know how the Maximite fires the injectors.

    Joe Berki


    The  Maximite has 20 I/O pins numbered 1 to 20, All of these pins
    can be configured as digital out puts or something else. The pin will
    put out 5 volts.

    You choose the pin you want to control the injector.

    Then it must first be configured. The instruction is "SETPIN pin,
    cfg" "pin" is simple the pin number you choose. Let say you choose
    pin number 2

    The instruction is then written SETPIN 2

    cfg stands for configure. Here is a list of possible configurations
    for most pins.

    0 Not configured or inactive 1 Analog input (pins 1 to 10) 2 Digital
    input (all pins and 5V tolerant on pins 11 to 20) 3 Frequency input
    4 Period input (pins 11 to 14) (pins 11 to 14) 5 Counting input
    (pins 11 to 14) 6 Interrupt on low to high input change (pins 1 to
    20, D0 to D8) for target 7 Interrupt on high to low input change
    (pins 1 to 20, D0 to D8) for target 8 Digital output  (all pins) 9
    Open collector digital output to 5V (pins 11 to 20, D0 to D13) In
    this mode the function PIN() will also return the output value.

    We want to make it and out put pin so we choose # 8

    The instruction is then written like this SETPIN 2, 8

    That is all  we have to do to configure pin #2 as an output pin. From
    now on it is an output pin.

    Now when we tell pin to go high the injector will be fired.

    PIN(2) = high   turns the injector pulse on 5V We wait.  The wait
    time is a function of the mass airflow sensor. PIN(2) = zero turn
    the injector pin off.

    That's it.

    You have to get a Maximite and play with it. You can use a volt
    meter to check your program. Programming is mostly trying things and
    see if it does what you want it to do.


    Paul Lamar

    Paul,

    The hardware is the easy part I wanted to know where to start with
    the software after the pins are configured. The 2 RX 8 sensors wil
    deliver a pulse when the CDI fires for both rotors. The Maximite
    looks at this and will fire the injector and keep it on based on the
    MAF sensor voltage. What computations need to take place to
    determine when to fire the injector based on ignition data? The
    pulses and the time between the first pulse and the second pulse will
    give unit time per revolution. The injection would be based on an
    event that already occurred. Does the rear rotor pulse drive the
    front rotor Maximize for injection?

    Joe Berki

    Do you have a Maximite yet?

    I had a brilliant idea yesterday to drastically simplify the code.

    You use a FOR NEXT loop to time the injection,

    The code would then look like this.

    PIN(2) = high   turns the injector pulse on 5V when the CAS occurs.
    FOR y = 1 to xxxx NEXT PIN(2) = zero  turn the injector pin off.

    xxxx becomes proportional to the mass air flow reading.

    That's it !!!!!! Your done !!!!!!!

    One Maximite per rotor.

    If I could only get a patent on this ROFL

    Paul Lamar

    Joe, the fuel system is independent from ignition. It starts up as
    soon as the mass airflow senses the cranking sequence.

    Steve Carlisle

    Google FOR NEXT LOOPs.

    There is at least a half dozen explanations. I was amazed.

    ---------------------------------------------------------------

    One of the things you must do when converting the MAF sensor data to
    the required width of the pulse is know how much fuel will be
    injected for a given pulse width.

    I found a great site for calculation the size of the injector you
    will need.


    http://www.witchhunter.com/injectorcalc1.php <http://www.witchhunter.com/injectorcalc1.php>
    <http://www.witchhunter.com/injectorcalc1.php <http://www.witchhunter.com/injectorcalc1.php> This screen capture jpg
    shows that you will need 4 injectors

    420 cc/min to generate 250 HP full rich at a BSFC of .65 pounds of
    fuel per HP per hour. The RX8 yellow injectors alone won't handle
    it.

    You will need 41 pounds per hour from each injector. 41 pounds is
    6.56 gallons per injector.

    Now we need to have a chart for the injector chosen that shows the
    flow rate per millisecond of opening time. I am working on it.


    Paul Lamar

    Paul, and more info from th guy that made the injector chart,
    http://users.erols.com/srweiss <http://users.erols.com/srweiss>

    Steve Carlisle


    Paul,


    I am still missing something. The CDI will work off of the 2 RX-8
    sensors mounted on the from cover using the one tit trigger wheel.
    Does the 2 Maxi Mite setup then use the 2nd gen CAS to drive it? I
    thought for some reason that that CAS could be eliminated.

    Thanks

    Joe Berki

    You mean the thing that looks like a distributor? Yes you can get rid
    of that. The 2 RX8 CAS's will trigger the Maximites as well. You can
    get a clean CAS pulse from the LM1815's on the dual CD board.

    BTW You can use the Maximite to calibrate an injector. You can set a
    pulse width using the Maximite and fire the injector once and measure
    the amount of fuel that comes out. You can trigger this with a push
    button in place of the CAS.

    Then you can set another different  pulse width and measure it
    again.

    Pretty soon you will have a chart that looks like this.

    The max rotary injector pulse width is about 7 ms. At 8000 RPM it
    takes only 8 ms to make one rev. So if you are firing the injector
    every rev you are limited to about 7 ms.  This is known as "timed
    injection".

    You need an injector that will squired enough fuel in 7 ms. What we
    did on the TTC is upped the fuel pressure so it would squirt more in
    a given pulse width.

    The video was done differently.  It is just to show the test set up.

    I did it in my back yard so I would not smell up my office :-)

    The Maximite  is very very handy device for all sorts of things.

    Paul Lamar



   Paul,

   I think I have got an understanding please review and let me know if I got it right.

   We fire the injector off of the RX-8 sensor 20 degrees BTDC and at the same time the CDI fires.

   Because of the configuration of the rotary, plugs on one side and P Port on the other, the
   ignition of lets call it #1 chamber occurs at the same time #3 chamber gets a load of fuel.

   Is this close to being accurate?

   Joe Berki


   Very good Joe. Well put.

   BTW Steve, I got the LM1815's. Thanks.

   Paul Lamar

Paul, I noticed they were delivered.
Thanks, Steve Carlisle


    The Rotary Engine free News Letter. Powered by Linux. If you want off
    the list PLEASE let me know and I will remove  you.  ACRE NL web
    site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2017 All world wide rights reserved.