Subject: EFI Maximite was EFI and CD ignition
From: paul lamar
Date: 9/10/2017, 8:32 AM
To: A10-Me-Earthlink



   Paul,

   I ordered 2 RX 8 crank angle sensors and am fabricating a bracket to
   mount the sensors.

   Room is tight due to modified water pump and heat shield for the
   augmenter.

   Could you explain how the Mighty Mite will use the pulse generated
   by the sensors and the one tit trigger wheel?

   The first pulse would be firing ignition by the CDI and the MM would
   know 20 degrees BTDC,

   Does it look for the second pulse to get a time frame for one rev of
   the Eshaft?

   What happens next?

   What would the code look like?

   Thanks

   Joe Berki

   There is no code for the CD ignition. The maximite does not need to
   be involved.

   The front rotor (car) fires from the first CAS at 22 degree BTDC.
   Then the second CAS 180 degrees later fires the rear rotor. That is
   all there is to it.

   That reminds me I need to check and see if I got the sample
   transformer for the CD system.

   Now the CAS can also be connected to the Maximite to fire the
   injectors after it checks the mass airflow sensor and figures out
   the correct pulse width.

   Paul Lamar

   This part is what I was trying to  understand I know the CDI is
   independent.

   I wanted to know how the Maximite fires the injectors.

   Joe Berki


   The  Maximite has 20 I/O pins numbered 1 to 20, All of these pins can
   be configured as digital out puts or something else. The pin will put
   out 5 volts.

   You choose the pin you want to control the injector.

   Then it must first be configured. The instruction is "SETPIN pin,
   cfg" "pin" is simple the pin number you choose. Let say you choose
   pin number 2

   The instruction is then written SETPIN 2

   cfg stands for configure. Here is a list of possible configurations
   for most pins.

   0 Not configured or inactive 1 Analog input (pins 1 to 10) 2 Digital
   input (all pins and 5V tolerant on pins 11 to 20) 3 Frequency input 4
   Period input (pins 11 to 14) (pins 11 to 14) 5 Counting input (pins
   11 to 14) 6 Interrupt on low to high input change (pins 1 to 20, D0
   to D8) for target 7 Interrupt on high to low input change (pins 1 to
   20, D0 to D8) for target 8 Digital output  (all pins) 9 Open
   collector digital output to 5V (pins 11 to 20, D0 to D13) In this
   mode the function PIN() will also return the output value.

   We want to make it and out put pin so we choose # 8

   The instruction is then written like this SETPIN 2, 8

   That is all  we have to do to configure pin #2 as an output pin.
    From now on it is an output pin.

   Now when we tell pin to go high the injector will be fired.

   PIN(2) = high   turns the injector pulse on 5V We wait.  The wait
   time is a function of the mass airflow sensor. PIN(2) = zero turn the
   injector pin off.

   That's it.

   You have to get a Maximite and play with it. You can use a volt meter
   to check your program. Programming is mostly trying things and see if
   it does what you want it to do.


   Paul Lamar

   Paul,

   The hardware is the easy part I wanted to know where to start with
   the software after the pins are configured. The 2 RX 8 sensors wil
   deliver a pulse when the CDI fires for both rotors. The Maximite
   looks at this and will fire the injector and keep it on based on the
   MAF sensor voltage. What computations need to take place to determine
   when to fire the injector based on ignition data? The pulses and the
   time between the first pulse and the second pulse will give unit time
   per revolution. The injection would be based on an event that already
   occurred. Does the rear rotor pulse drive the front rotor Maximize
   for injection?

   Joe Berki

   Do you have a Maximite yet?

   I had a brilliant idea yesterday to drastically simplify the code.

   You use a FOR NEXT loop to time the injection,

   The code would then look like this.

   PIN(2) = high   turns the injector pulse on 5V when the CAS occurs.
   FOR y = 1 to xxxx NEXT PIN(2) = zero  turn the injector pin off.

   xxxx becomes proportional to the mass air flow reading.

   That's it !!!!!! Your done !!!!!!!

   One Maximite per rotor.

   If I could only get a patent on this ROFL

   Paul Lamar

   Joe, the fuel system is independent from ignition. It starts up as
   soon as the mass airflow senses the cranking sequence.

   Steve Carlisle

   Google FOR NEXT LOOPs.

   There is at least a half dozen explanations. I was amazed.

   ---------------------------------------------------------------

   One of the things you must do when converting the MAF sensor data to
   the required width of the pulse is know how much fuel will be
   injected for a given pulse width.

   I found a great site for calculation the size of the injector you
   will need.


   http://www.witchhunter.com/injectorcalc1.php <http://www.witchhunter.com/injectorcalc1.php> <http://www.witchhunter.com/injectorcalc1.php <http://www.witchhunter.com/injectorcalc1.php>>
   <http://www.witchhunter.com/injectorcalc1.php <http://www.witchhunter.com/injectorcalc1.php> <http://www.witchhunter.com/injectorcalc1.php <http://www.witchhunter.com/injectorcalc1.php>>>


   This screen capture
   jpg shows that you will need 4 injectors

   420 cc/min to generate 250 HP full rich at a BSFC of .65 pounds of
   fuel per HP per hour. The RX8 yellow injectors alone won't handle
   it.

   You will need 41 pounds per hour from each injector. 41 pounds is
   6.56 gallons per injector.

   Now we need to have a chart for the injector chosen that shows the
   flow rate per millisecond of opening time. I am working on it.


   Paul Lamar

   Paul, and more info from th guy that made the injector chart,
   http://users.erols.com/srweiss <http://users.erols.com/srweiss <http://users.erols.com/srweiss> <http://users.erols.com/srweiss <http://users.erols.com/srweiss>>>
   <http://users.erols.com/srweiss <http://users.erols.com/srweiss> <http://users.erols.com/srweiss <http://users.erols.com/srweiss>> <http://users.erols.com/srweiss <http://users.erols.com/srweiss> <http://users.erols.com/srweiss <http://users.erols.com/srweiss>>>

   Steve Carlisle


   Paul,


   I am still missing something. The CDI will work off of the 2 RX-8
   sensors mounted on the from cover using the one tit trigger wheel.
   Does the 2 Maxi Mite setup then use the 2nd gen CAS to drive it? I
   thought for some reason that that CAS could be eliminated.

   Thanks

   Joe Berki

   You mean the thing that looks like a distributor? Yes you can get
   rid of that. The 2 RX8 CAS's will trigger the Maximites as well. You
   can get a clean CAS pulse from the LM1815's on the dual CD board.

   BTW You can use the Maximite to calibrate an injector. You can set a
   pulse width using the Maximite and fire the injector once and
   measure the amount of fuel that comes out. You can trigger this with
   a push button in place of the CAS.

   Then you can set another different  pulse width and measure it
   again.

   Pretty soon you will have a chart that looks like this.

   The max rotary injector pulse width is about 7 ms. At 8000 RPM it
   takes only 8 ms to make one rev. So if you are firing the injector
   every rev you are limited to about 7 ms.  This is known as "timed
   injection".

   You need an injector that will squired enough fuel in 7 ms. What we
   did on the TTC is upped the fuel pressure so it would squirt more in
   a given pulse width.

   The video was done differently.  It is just to show the test set up.

   I did it in my back yard so I would not smell up my office :-)

   The Maximite  is very very handy device for all sorts of things.

   Paul Lamar



   Paul,

   I think I have got an understanding please review and let me know if
   I got it right.

   We fire the injector off of the RX-8 sensor 20 degrees BTDC and at
   the same time the CDI fires.

   Because of the configuration of the rotary, plugs on one side and P
   Port on the other, the ignition of lets call it #1 chamber occurs at
   the same time #3 chamber gets a load of fuel.

   Is this close to being accurate?

   Joe Berki


   This is some great work, which is very helpful to many of us
   CDI/EFI challenged folks!

   Questions:  since the injectors are basically spraying into the
   intake manifold, is the injector timing really critical - especially at
   high rpm?  If so, are you saying that the injector duration can be
   simply a function of MAF, manifold pressure or rpm, unrelated to timing?

   If the stock rx8 CAS can generate an appropriate pulse, would it
   make sense to mount a second CAS 180 degrees off, and modify a trigger
   wheel to fire the  CASs at 22 BTDC?

   Scott Gettings

   Yes super simple. You just measure the mass air flow sensor and
   delay that long.
   You need a chart on the injectors your using so you know how much
   fuel is injected
   per ms. You can make adjustment in these numbers by adjusting the
   fuel pressure
   regulator.

   Actually to keep the software  real simple you can use a shaft
   connected to the fuel
   pressure regulator to manually control the mixture ratio. Similar
   to what we did
   on the manually controlled TTC waste gate.
   All the EFI must do is start and keep the engine running
   using the mass airflow sensor.

   It is also typical for a carburettor equipped  aircraft engine.

   Patent applied for :-) Not really :-)

   The injection happens at the same time as the spark.
   I don't think it is critical at all as the next face is opening and
   will receive the fuel and air.
   The P-port intake never sleeps :-)

   BTW to probability of software  bugs is proportional to the number
   of lines of software cubed.
   Same goes for understanding it

   Yes on the second CAS. That is what we are designing the CD
   ignition based on.
   Again simplicity. Easy to understand and easy to trouble shoot.

   Now you have a bit of redundancy. If one CAS fails the engine still
   runs on one rotor.

   Paul Lamar

   To vary the injector timing to test for best BSFC and power at cruise
   RPM, a separate plate mounted on the front cover could be installed with
   slotted bolt holes. This way injector timing can be changed with minimal
   lines of code. For automotive use the spark signal is actually used for
   the next cylinder in the firing order. The signal is 45°to 90° before
   required but the software retards from there. I think injection timing
   is worked this way also.

   On a rotary for aircraft, the running RPM is fairly constant so finding
   the optimum injection timing should be fairly simple on a dyno or by
   experimenting with making and documenting changes and test flights.

   Simple to try changing injection between rotors also by switching the
   wiring between CAS sensors for firing the injectors.

   Dale Davies


   Paul,

   The RX-8 sensors and connectors  have arrived.
   I do not think the one tit trigger wheel that I posted earlier will work
   as it pushes the outer rime too close to duct work.
   I would like to fab an aluminum plate that looks like a donut with the
   correct hole pattern to bolt to the 2 groove pulley and Shaft hub.
   I could then drill and tap the plate and install a steel screw/bolt at
   20 degrees BTDC to trigger every thing.

   This will give me enough room to mount the sensors ( I hope).
   For locating purposes for TDC the groove and key on the hub  go at 9:00
   and the yellow or white mark on the pulley lines up with the pointer?

   What does the red mark signify?

   Need to order Maxi Mites

   Thanks for any help

   Joe Berki

   Move the trigger wheel to the out side of the pulley as shown here.
   It  is mounted on an extension of the e-shaft in the form of an aluminum
   spacer with four long bolts..

   The four bolts are not symmetrical so be careful when you make
   it. You will need some one with a lathe.

   It fits inside the e-shaft pulley.

   The trigger plate  must be balanced and that is what the large hole does.

   Use the apex seal oil injector bolt holes to make a bracket
   that holds one CAS.

   A water jet would be ideal to make the one tit trigger plate.

   Let me me know if you cannot get it made.

   Do not worry about the injection timing. It will be controlled
   and timed by the two CAS's for the ignition. That will work fine.

   The spark plugs are on one side and the injectors are more
   or less 180 degrees away on the other side.

   ---------------------------------------------------

   Here is a better shot of what it will look like.

   Paul Lamar

   How about designing a PIP that changes position! Way more simple!

   Steve Carlisle


   I have no idea what you mean Steve. PIP?

   Joe, please take a picture of the front of your engine.
   I need to see what year the front cover is.

   Paul Lamar

What do you call that little thing that activates the sensor?

Steve Carlisle

You mean the tit? A tit that changes position by centrifugal force?

IMHO Would not be worth the cost.

Paul Lamar


   The Rotary Engine free News Letter. Powered by Linux. If you want off
   the list PLEASE let me know and I will remove  you.  ACRE NL web
   site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2017 All world wide rights reserved.