Subject: Electric oil pump and coolant pump power requirement
From: paul lamar
Date: 9/30/2017, 11:44 PM
To: A10-Me-Earthlink



    Paul, and group

    We are thinking of building a 13B engine for our airplanes  and
    possibly for my helicopter project.

    We are contemplating using an electric coolant pump and also an
    electric oil pump.

    We were thinking of using the Toyota MR2 power steering pump for
    oil, and some other, like a Messiere type pump for the coolant.

    Do you know the power requirements for these two pumps?

    We have already used an MR2 oil pump for our electric car project.

    Zoltan Szakaly and Mark Szakaly

    Yes and an electric cooling pump is a bad joke. It takes 3 HP to cool
    a rotary.  2,250 watts at 12 volts that is  187 AMP!!!!! The fuse on
    a Mezziewr is 20 amps. Good luck :-)

    Paul Lamar


    I wonder if you have any information on the oil pressure and flow
    rates? I imagine the oil pump is just driven by the engine directly
    and so it is hard to get any data on it. I would just like to get
    your ideas of the oil pressure and amount of oil used. I know that
    you have an oil pan you developed. How long does it take to fill up?
    Thank you for your response.

    Zoltan  Szakaly


    Thank you for your quick response.

    You have answered my question regarding the coolant flow
    requirement.

    But what is the necessary oil pressure and oil flow requirement? What
    is the meaning of the colors on your coolant flow diagram?

    Zoltan  Szakaly

    As I recall the old stock engine of around 150 HP used 30 gallons
    an    hour.   I would up that as we are talking a lot more HP

    Paul Lamar

    To measure the oil flow you would need to install a flow measurement device between the pump and the engine. Remember the pressure regulator dumps excess oil to the pan or tank. Best would be to measure both to determine what is actually happening in the oil system.Of course the pump flow rate can be calculated considering pump RPM, but the important information is the actual flow to the engine.

    Also remember the pressure regulator only limits maximum oil pressure. Before the pressure regulator opens the pressure is determined as a balance of pump flow restricted by bearing clearances and cooling squirter. Thus worn bearings will create pressure issues at low pump flow rates as at idle.

    Ford Cleveland and Modified engines were notorious for this. At about 100k miles the oil light would start to flash after driving a few miles and stopping at a light or stop sign. People would come in to have the oil pump replaced. I would replace the worn main and conn rod bearings and while mostly there, replace the timing chain with a double roller chain assembly. Good for another 100k miles.customer would be mad I did not replace the pump. I always inspected them and determined they were serviceable. Offered to replace the pump if they were not satisfied after driving it, for free. Never had to do that.

    Dale Davies

    I wish we had a flow rate sensor on the TTC engine.

    Paul Lamar

    Where is the pressure regulator located?

    Dale Davies

    Here it is.

    Paul Lamar

Looks like you have at least two pressure pump outlets to the engine; main bearings.
The simplest measurement device is a turbine. These require 10 pipe diameters upstream and 5 downstream for accurate measurement. To totalizing the output you need either a tantalizer which are readily available in oilfield suppliers or a Maximite could do the math and do more than one turbine. PLC's for process control can do this also, so if they can be programmed for it a Maximite can also.

Shop provers run water through the turbine and the wayer is measured or weighed. The pulse counts off the turbine are tallied to give a pulses per volume. Once that is known the totalizer or maximite is programmed for that turbine. Turbines come in many sizes depending on flow rate. If I remember correctly a 1" turbine is good for 27 to 270 barrels per day. I will look the sizing up and get back.

Dale Davies


That is correct there is an oil gallery that runs through the top of the
engine. High pressure oil is fed in at both ends.

There are three scavenge outlets. One for each main bearing
and one for the rotor cooling oil.

Paul Lamar


    The Rotary Engine free News Letter. Powered by Linux. If you want
    off the list PLEASE let me know and I will remove  you.  ACRE NL web
    site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2017 All world wide rights reserved.