12
Hey Paul,
Based on your book and our many discussions, it looks like the
largest water radiator I can practically fit in front of the engine
will be a pair (cross-counterflow) of about 20x16” radiators, using
a 45 degree mounting angle. The plumbing is feasible in this
configuration.
The stock RX8 radiator is 17.5x26x2”, with a core area of 14.5x25 =
362 sq inches of frontal area. It is about 1.5” thick. Total
cooling volume is 543 cubic inches, but this is way too wide to fit.
The Neon radiators are 24.7x14.7x2”, with a core area of
23.5x11.7x1.5”. This is 274 sq inches and 411 cubic total volume.
They use a 1 3/8” fitting as does the RX8. However they are still
too wide. If I cut 4-5 inches off one end of the neon radiator to
make if fit, I would have about 20x11.7 frontal area of core. This
is 234 sq inches or 351 cubic inches. Two of these would total 468
sq inches and 700 cubic inches. The two of these together will be
have more frontal and volume area compared to the stock radiator.
My questions are: Will reducing the radiator size (each will have a
volume of 64% of stock), plus having twice as long of a fluid path
through 2 radiators, possibly present a significant resistance to
water flow?
I assume we are still looking at intake ducts of about 15% of the
frontal area, which in this case would be 35 square inches. This
would allow ducting for other functions (air intake, cooling tube
and oil radiators). I have a couple of decent options for the oil
coolers, and should be able to have larger areas and volume than
stock.
Should we be using smaller main pulleys to under drive the water
pump and alternator due to a target RPM of about 7,000?
Thanks,
Scott Gettings
Your core thicknesses are off. The Neon is only about 1 inch thick
or less. Some modern rads are 5/8th inch thick. The old rule of 600
cubic inches does not apply anymore. The Kays and London wedge or
even better S shaped diffusers are far more important.]
The Kuchmen and Weber will work if the duct is long enough. It is now
more like 450 cubic inches.
Which of these configurations are most like what you have in mind?
Mounting the rads back by the gear box is a good idea using the Kays
& London wedge looks like the best. The ducts can be quite thin
alongside the engine. The prop can suck some air out.
Paul Lamar
Hey Paul,
The side configuration will work OK for the oil coolers, but the
water radiator(s) needs to be upfront for a variety of reasons. I
can duct around the sides of a front radiator if it is not too wide,
on the order of about 20 inches. So a K&L duct should be feasible for
the side or rear oil coolers, as per your drawing. With the front
rads angled at 45degrees, the duct up front would obviously be very
short: just a few inches on the top and about 15” on the bottom.
Do you think that a pair of Neon radiators (plumbed in serial as a
counterflow) cut down to about 20”wide will work from a water
flow/pressure perspective?
Do you have a recommendation regarding the main pulley size? Stock
or under Drive?
Thanks
Scott Gettings
Wide? Do you mean along the length of the tubes? I don't think that
is possible.
However there are companies out there that make furnace brazed rads
from scratch.
Send me a sketch of what you have in mind. I take it you are planing
on mounting them on the cabin roof in front of the engine.
There is nothing wrong with a bit of plumbing :-)
Stock pulley is fine. You will not turn 11,000 RPM :-)
To cut down the width of those cross counter flow header tanks is
going to take a tig welding pioneer :-) I suggest a lot of wet rags
up under the headers. As it was we had a leak in the TTC cross
counter flow due to tig welding.
Those rads are brazed at only 1100 F.
Ideally the headers should be designed for cross counter flow before
they are brazed.
Paul Lamar
Paul,
As long as a radiator is being narrowed by removing whole rows of tubes,
my welder can shorten and re-close the headers and place the water
fittings in an optimal location. The headers would not be otherwise
altered.
The first attached image is a mockup of two 16 x 20 radiators in a cross
counterflow configuration. I only have 15 inches from the engine to the
front of the cowling and of course the engine is about 14 inches high.
I was planning on having the back radiator fed from the bottom/rear, the
interconnect on the top of both radiators and a return from the
bottom/rear of the front radiator. This would give a minimal short
distance to the water pump.
The other attached images show a stock RX8 radiator in the same
location, but it is obviously too big. You can see the headers are on
the top and the bottom, so the radiator can be shortened side to side
without removing the headers.
If the radiators are not too big, I can get the largest frontal area
with the least amount of plumbing by using this type of configuration.
Following the completion of these components, I was planning on creating
the ducting for the oil radiators in the rear, cool side of the cowling.
By the way, when I tapped off of my crank angle sensor to measure the
output, I found my RX eight radiator was leaking at the edge of the
plastic tank. The piece of junk only lasted 12 years! . So I replaced
it with an all aluminum model. It is a very tight fit!
Scott Gettings
You need to lay it down more so you only have 3 or 4 inches above
the canopy for the air intake.
Paul Lamar
The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove you. ACRE NL web
site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.