Subject: coupling for my single rotor 12 e
From: paul lamar
Date: 11/16/2017, 9:56 PM
To: A10-Me-Earthlink


12 e

Hi Paul,


This is the cush drive I have built for my single rotor.

It is machined out of 6061T6 billet on an old lathe and cheep Chinese
mill. The diameter is approx 4.7 inches, the inserts are urethane rod
at 1.25 inches in diameter. I am going to start with the green
urethane which is the lowest Shore hardness available here. the photo
shows a yellow grade which is slightly harder. The rod cuts well with
a sharp tungsten blade on a drop saw.

I have also had a new flywheel machined from billet 4140, as I was
not happy with the flex plate. The whole assembly has been
dynamically balanced.

Andrew Campbell.


Yes. That looks like it is going to work. Good idea. You should use
silicone rubber. Good to 500 F. There is a certain amount of energy
going into those dampers.

Urethane is only good to about 200 F.

Paul Lamar

You will need a sleeve or something around the outside of the
inserts. After they have deformed a little they will no longer be
contained and will fly out.

Bill Bradburry They will have to deform a great deal before that
happens , if this becomes a problem I will use a slightly harder
compound. I don't really have the machine tools for production but I
am happy to supply a drawing. Andrew.


Andrew, What format can you support with the drawing? I would be
grateful for a copy. I have Rhino.

Craig Smith


Hi Craig, I machined this from a sketch, I don't have any cad
drawing programs so the best I can do would be a drawing with
dimensions. I am going to do some torque measurements shortly to
decide on the Shore hardness  that I will be using . Bill had a valid
point, I am only going to produce 130hp max at 7500 rpm so the torque
will be in the region of 91ft/lbs. this can be applied with a torque
wrench no problem. I will then be able to measure the deformation of
the compound and know the most appropriate grade to use.

If urethane does not hold up in this application and I suspect that
the way the compound is being loaded, it will, then I will look at
other materials.

The product is readily available in NZ so if you have a problem with
sourcing it I would be happy to ship it to you.

I will do  a Drawing and post it, might take a few days. The
dimensions are able to be modified to suit your particular set or
conditions, the only thing to bear in mind is the way the rubbers are
captured. The two halves are identical. The only thing that may vary
would be the height and bolt fixings. The overall outside diameter
could be increased and more rubbers inserted for higher torque
requirements. As the rubbers are held in close contact with aluminum
I am expecting a good rate of cooling on the compound.

Andrew Campbell.

The torque pulses are severe in a one rotor so urethane is not going
to work for long. Our TTC coupling is working great with up to 650
HP. Most power so far has been  500 HP. That is 500 degree Fahrenheit
silicon rubber you see in the pictures.

Paul Lamar OK It looks as if I will have to use silicone rubber.
Andrew Campbell.

Good I don't want you killing yourself.

Paul Lamar



No I dont want that either, I have been in touch with some
guys here that specialise in silicone rubber products, I will come up
with a spider that will do the job and once the mould is finalised it
may be of use to other guys building single rotor units.
    Andrew Campbell.

------------------------------------------------------------------
Please  add your questions or comments  at the end of the thread.
Not the beginning.

I am going to enforce that rule. If people don't do that it will not be forwarded.
My ISP changed the rules.

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.