Subject: coupling for my single rotor 12 d
From: paul lamar
Date: 11/17/2017, 12:03 PM
To: A10-Me-Earthlink




12 d

  Hi Paul,


  This is the cush drive I have built for my single rotor.

  It is machined out of 6061T6 billet on an old lathe and cheep Chinese
  mill. The diameter is approx 4.7 inches, the inserts are urethane rod
  at 1.25 inches in diameter. I am going to start with the green
  urethane which is the lowest Shore hardness available here. the photo
  shows a yellow grade which is slightly harder. The rod cuts well with
  a sharp tungsten blade on a drop saw.

  I have also had a new flywheel machined from billet 4140, as I was
  not happy with the flex plate. The whole assembly has been
  dynamically balanced.

  Andrew Campbell.


  Yes. That looks like it is going to work. Good idea. You should use
  silicone rubber. Good to 500 F. There is a certain amount of energy
  going into those dampers.

  Urethane is only good to about 200 F.

  Paul Lamar

  You will need a sleeve or something around the outside of the
  inserts. After they have deformed a little they will no longer be
  contained and will fly out.

  Bill Bradburry They will have to deform a great deal before that
  happens , if this becomes a problem I will use a slightly harder
  compound. I don't really have the machine tools for production but I
  am happy to supply a drawing. Andrew.


  Andrew, What format can you support with the drawing? I would be
  grateful for a copy. I have Rhino.

  Craig Smith


  Hi Craig, I machined this from a sketch, I don't have any cad
  drawing programs so the best I can do would be a drawing with
  dimensions.  I am going to do some torque measurements shortly to
  decide on the Shore hardness  that I will be using . Bill had a valid
  point, I am only going to produce 130hp max at 7500 rpm so the torque
  will be in the region of 91ft/lbs. this can be applied with a torque
  wrench no problem. I will then be able to measure the deformation of
  the compound and know the most appropriate grade to use.

  If urethane does not hold up in this application and I suspect that
  the way the compound is being loaded, it will, then I will look at
  other materials.

  The product is readily available in NZ so if you have a problem with
  sourcing it I would be happy to ship it to you.

  I will do  a Drawing and post it, might take a few days. The
  dimensions are able to be modified to suit your particular set or
  conditions, the only thing to bear in mind is the way the rubbers
  are captured. The two halves are identical. The only thing that may
  vary would be the height and bolt fixings. The overall outside
  diameter could be increased and more rubbers inserted for higher
  torque requirements. As the rubbers are held in close contact with
  aluminum I am expecting a good rate of cooling on the compound.

  Andrew Campbell.

  The torque pulses are severe in a one rotor so urethane is not going
  to work for long. Our TTC coupling is working great with up to 650
  HP. Most power so far has been  500 HP. That is 500 degree Fahrenheit
  silicon rubber you see in the pictures.

  Paul Lamar


Are the most current versions of the CAD drawings available to share?
We have lots of CNC and fabrication resources here on the Space Coast.
I could get estimates on some small volume production runs.

Scott Gettings

The exact design depends on the gear box input shaft.
Here is the jpg and iges drawings for the design.

Paul Lamar

------------------------------------------------------------------
Please  add your questions or comments  at the end of the thread.
Not the beginning.

I am going to enforce that rule. If people don't do that it will not be
forwarded.
My ISP changed the rules.

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.