Subject: coupling for my single rotor 12 g
From: paul lamar
Date: 11/19/2017, 5:19 PM
To: A10-Me-Earthlink


12 g

Hi Paul,


This is the cush drive I have built for my single rotor.

It is machined out of 6061T6 billet on an old lathe and cheep
Chinese mill. The diameter is approx 4.7 inches, the inserts are
urethane rod at 1.25 inches in diameter. I am going to start with the
green urethane which is the lowest Shore hardness available here. the
photo shows a yellow grade which is slightly harder. The rod cuts
well with a sharp tungsten blade on a drop saw.

I have also had a new flywheel machined from billet 4140, as I was
not happy with the flex plate. The whole assembly has been
dynamically balanced.

Andrew Campbell.


Yes. That looks like it is going to work. Good idea. You should use
silicone rubber. Good to 500 F. There is a certain amount of energy
going into those dampers.

Urethane is only good to about 200 F.

Paul Lamar

You will need a sleeve or something around the outside of the
inserts. After they have deformed a little they will no longer be
contained and will fly out.

Bill Bradburry They will have to deform a great deal before that
happens , if this becomes a problem I will use a slightly harder
compound. I don't really have the machine tools for production but I
am happy to supply a drawing. Andrew.


Andrew, What format can you support with the drawing? I would be
grateful for a copy. I have Rhino.

Craig Smith


Hi Craig, I machined this from a sketch, I don't have any cad drawing
programs so the best I can do would be a drawing with dimensions. I
am going to do some torque measurements shortly to decide on the
Shore hardness  that I will be using . Bill had a valid point, I am
only going to produce 130hp max at 7500 rpm so the torque will be in
the region of 91ft/lbs. this can be applied with a torque wrench no
problem. I will then be able to measure the deformation of the
compound and know the most appropriate grade to use.

If urethane does not hold up in this application and I suspect that
the way the compound is being loaded, it will, then I will look at
other materials.

The product is readily available in NZ so if you have a problem with
sourcing it I would be happy to ship it to you.

I will do  a Drawing and post it, might take a few days. The
dimensions are able to be modified to suit your particular set or
conditions, the only thing to bear in mind is the way the rubbers are
captured. The two halves are identical. The only thing that may vary
would be the height and bolt fixings. The overall outside diameter
could be increased and more rubbers inserted for higher torque
requirements. As the rubbers are held in close contact with aluminum
I am expecting a good rate of cooling on the compound.

Andrew Campbell.

The torque pulses are severe in a one rotor so urethane is not going
to work for long. Our TTC coupling is working great with up to 650
HP. Most power so far has been  500 HP. That is 500 degree
Fahrenheit silicon rubber you see in the pictures.

Paul Lamar


Are the most current versions of the CAD drawings available to
share? We have lots of CNC and fabrication resources here on the
Space Coast. I could get estimates on some small volume production
runs.

Scott Gettings

The exact design depends on the gear box input shaft. Here is the jpg
and iges drawings for the design.

Paul Lamar

Andrew,

Here is some round silicone rubber rod you may be able to use from
McMaster. If you cannot have it shipped directly to NZ I can buy it
for you and ship it to NZ Let me know what lengths you need to cut
the cost of shipping.

Paul Lamar

Hi, from [Andrew] your photos; I would radius the inside and outside
corners of the metal pockets for the elastomer rods. In one of the
charts that Paul sent you  can see that the peak torque of a single
rotor is at least twice that of average torque. The elastomer has to
deform to work and sharp metal edges will chew the rods up in short
order.

Murry I. Rozansky


Thanks Paul. The diameter needs to be 1.25" I hope to be able to have
the complete spider cast here. A spider is a term we give to the
rubber component if the individual components are held together as a
complete      casting,     a bit like a spiders web. This allows the
unit to hold together by overcoming the problem of centrifugal
effect. I am about to tests on the rubbers that I have to better
determine the Shore hardness that I need. I remember now that the
diagram on torque pulses was posted some time ago. I will let you
know how I get on.

Murry, Yes absolutely the unit is still a work in progress.

Andrew Campbell.



Unfortunately  1.25 round is not available. One inch is the largest.
If made from a block it does not turn well on a lathe. It band saws
much better.

Paul Lamar

   It will turn nicely if you freeze it first.  Depending on the amount
of turning, a re-
   freeze my be necessary.  Work well for any type of rubber.  I have
used dry ice
   and alcohol which give a temp of approx. -175°F.  Just soak the part
for a few
   minutes and then be sure not to touch is without gloves or a tool. A
sharp high
   speed steel cutter works well.

   Gary Knutson


------------------------------------------------------------------
Please  add your questions or comments  at the end of the thread. Not
the beginning.

I am going to enforce that rule. If people don't do that it will not
be forwarded. My ISP changed the rules.

The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.