Subject: Trouble with the TTC water injection. 12d
From: paul lamar
Date: 12/15/2017, 3:49 PM
To: A10-Me-Earthlink


12  d

 First we had trouble with the Oz M&W CD ignition. Since we have no
 alternator or voltage regulator the battery voltage would drop below
 11 Volts and the Oz ignition would quit.

 We got the first indication of this up at Cal City after the first
 test  flight.

 We checked around and found that the drag racers used an 18 volt
 battery for just the ignition as they don't run an alternator
 either.

 We found a small 20 volt battery and installed that just for the
 ignition.

 Unfortunately the wire that fed the ignition also fed the water
 injection solenoid. That caused a transistor inside the Motec 800 to
 fail as 20 volts on a 15 ohm solenoid caused a current  1.33 AMPs.
 Ouch!

 If the water injection fails the air intake temperature goes to 300 F
 probably raising the rotor temperature to well over 500 F. Now that
 could melt the side seals if you are not using Teflon encapsulated
 side seal O-rings. I think we are seeing signs of that now. The stock
 seals o-rings are not up to it. I had a Cosmo that had melted side
 seal O-ring that smoked like made on start up but I drove it for ten
 years like that.

 Back to todays problem. We reduced the voltage on the solenoid to 12
 volts.

 Worked for a flight or two and then we failed another transistor in
 the Motec 800.  We were going to run out of transistors soon. I
 measured the ohms on the old solenoid and found it to be 12 ohms.
 Apparently some of the coils had shorted. We bought a new one and
 that was back up to 15 ohms.

 Well that is still  .8 amp. Quite a lot for 8 or 10 year old Motec
 800 transistors. Modern transistor in the last few years are far more
 efficient as they are used in LED lighting and everything else
 including cell phones and computers.

 So today's mod was use a 5 ohm 10 watt resister in series with the 15
 ohm solenoid to reduce the transistor current to .6 amps. If the
 second to last transistor fails we may need to get the Motec 800
 repaired.

 I did not take the Motec apart to check the transistors or change the
 transistors for more modern versions  but I probably could if
 needed.


 Paul Lamar


Paul,
               You think you have problems!!!  I stripped down my engine as it was leaking combustion into the water jacket.  All went well until I rushed to start and check it the problem had "gone away".

A couple of clicks as in a flat battery was all I got.  Went and got a fully charged battery off the tractor--- still just a ":click" Then I suddenly realized that I had not connected the earth to the motor --- It was trying to earth through the ECU!! It only blew a big hole in the mother board.  Freight and repair--- $1500  later, now the starter now turns very well with TWO earth leads.  How can I be so stupid??  I think it comes naturally.

Neil Unger.


"leaking combustion into the water jacket"
Sounds like you had the old neoprene water jacket O-rings :-)

Paul Lamar

Hi Paul,
   Does the RX8 renesis have Teflon or neoprene seals.


Chris Hoskins  in NZ

They are a combination of silicone and Teflon.

Probably to get around the patent. They are square. the side nearest
the combustion chamber is Teflon. The rest is silicone.

Paul Lamar




------------------------------------------------------------------
 Please  add your questions or comments  at the end of the thread. Not
 the beginning.

 I am going to enforce that rule. If people don't do that it will not
  be forwarded. My ISP changed the rules.

 The Rotary Engine free News Letter. Powered by Linux. If you want
 off the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2017 All world wide rights reserved.








---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus