Subject: trouble with the TTC water injection. 12C
From: paul lamar
Date: 12/15/2017, 3:43 PM
To: A10-Me-Earthlink


 12 C

 First we had trouble with the Oz M&W CD ignition. Since we have no
 alternator or voltage regulator the battery voltage would drop below
 11 Volts and the Oz ignition would quit.

 We got the first indication of this up at Cal City after the first
 test  flight.

 We checked around and found that the drag racers used an 18 volt
 battery for just the ignition as they don't run an alternator
 either.

 We found a small 20 volt battery and installed that just for the
 ignition.

 Unfortunately the wire that fed the ignition also fed the water
 injection solenoid. That caused a transistor inside the Motec 800 to
 fail as 20 volts on a 15 ohm solenoid caused a current  1.33 AMPs.
 Ouch!

 If the water injection fails the air intake temperature goes to 300
 F probably raising the rotor temperature to well over 500 F. Now
 that could melt the side seals if you are not using Teflon
 encapsulated side seal O-rings. I think we are seeing signs of that
 now. The stock seals o-rings are not up to it. I had a Cosmo that had
 melted side seal O-ring that smoked like made on start up but I drove
 it for ten years like that.

 Back to todays problem. We reduced the voltage on the solenoid to 12
 volts.

 Worked for a flight or two and then we failed another transistor in
 the Motec 800.  We were going to run out of transistors soon. I
 measured the ohms on the old solenoid and found it to be 12 ohms.
 Apparently some of the coils had shorted. We bought a new one and
 that was back up to 15 ohms.

 Well that is still  .8 amp. Quite a lot for 8 or 10 year old Motec
 800 transistors. Modern transistor in the last few years are far
 more efficient as they are used in LED lighting and everything else
 including cell phones and computers.

 So today's mod was use a 5 ohm 10 watt resister in series with the
 15 ohm solenoid to reduce the transistor current to .6 amps. If the
 second to last transistor fails we may need to get the Motec 800
 repaired.

 I did not take the Motec apart to check the transistors or change
 the transistors for more modern versions  but I probably could if
 needed.


 Paul Lamar


 Paul, You think you have problems!!!  I stripped down my engine as it
 was leaking combustion into the water jacket.  All went well until I
 rushed to start and check it the problem had "gone away".

 A couple of clicks as in a flat battery was all I got.  Went and got
 a fully charged battery off the tractor--- still just a ":click" Then
 I suddenly realized that I had not connected the earth to the motor
 --- It was trying to earth through the ECU!! It only blew a big hole
 in the mother board.  Freight and repair--- $1500  later, now the
 starter now turns very well with TWO earth leads.  How can I be so
 stupid??  I think it comes naturally.

 Neil Unger.


 "leaking combustion into the water jacket" Sounds like you had the
 old neoprene water jacket O-rings :-)

 Paul Lamar



 Paul,    Did, plus I suspect that my "expert" builder
 resused the original O rings.  Now with RWS O rings.  MUch better
 quality.


Neil.

What is RWS?

Silicone is the only O ring material that will tolerate
500 F. Of course Teflon will too but it is not rubbery and that
is why it is not used alone.

I have discovered that a lot of these Wankel racers are surprisingly uneducated.
It's like they have not read Kenichi Yamamoto's book Rotary Engine.

I doubt most of them are qualified mechanical engineers.

I see so many errors on youtube.

Jack Yamaguchi wrote a couple of good books called RX7 and RX8.
A lot of them have to do with the history of Mazda Wankel R&D.

John Dinkel on here edited both of  them.
Very good histories  of Wankel R&D

Mazda published a rare book called Rotary Engine in 2003
Press Information.
Excellent history of rotary engine development at Mazda.

May be John Dinkel wrote it.

I think there are one or two others out there.

Paul Lamar

 ------------------------------------------------------------------
 Please  add your questions or comments  at the end of the thread.
 Not the beginning.

 I am going to enforce that rule. If people don't do that it will not
 be forwarded. My ISP changed the rules.

 The Rotary Engine free News Letter. Powered by Linux. If you want off
 the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2017 All world wide rights reserved.