Subject: Neals Ungers gear box
From: paul lamar
Date: 12/17/2017, 5:13 AM
To: A10-Me-Earthlink


12 J

Does anyone have a rd1c installation guide or advice. I want to
check before bolting the psru back up for engine runs. Wasn't there a
viton seal recommended to seal the bearing/thrust washer stack
against the motor mount plate?    Alex Molteno Yes but I recommend

Teflon. Paul Lamar


Alex, The teflon disc goes between the input gear and the inner
surface of the planetry reduction to stop metal to metal when you
pull power and the input shaft can be drug forwards.  The prop shaft
goes through the center of the teflon disc. Bearings go against the
plate, and make sure you have a low pressure seal in the plate. A low
pressure seal has one lip only, a high pressure, two or double lip.
Little pressure in the housing so the low pressure seal does a much
better job of sealing as is more flexible.

Neil Unger.

Ok thanks Neil,

Alex Molteno


Hi Neil, do you have an illustration or picture to show the location
of the discs on your drive. My engine has run time on a stand for
about an hour when it belonged to Milo Burroughs and there is a
slight bit of wear on Tracys motor mount plate at the rear of the
drive. I initially figured thats what you were talking about when you
said it needs the teflon disc, to stop any metal on metal rubbing
when the shaft is not being pulled forward, for instance when the
prop is driving the engine on steep descent,

but as i understand it, you recommend to put another disc at the
opposite end too for when power is applied and the shaft is pulled
forward to metal on metal contact

So 2 discs needed then. Do you remember what thickness you are using
for the forward disc, so it doesn't tear it up?

Alex Molteno

That is kind of surprising as those are thrust roller bearings. They
should not need teflon.

Paul Lamar


Alex, There is one nylon or teflon disc only, not two. The
Nylon disc which tracy called the "snubber" bearing goes between the
front face of the gear on the input shaft and the inner face of the
planetry.  The prop shaft comes through the front of the planetry
(splined) and then through the "snubber" disc with the polished end
of the prop shaft then finishing up inside the center of the input
shaft which has a brass bush pressed into it. THis makes both the
prop shaft and the input shaft almost rigid. The bearing stack which
consists of, 2 thick thrust washers which are each end of the bearing
stack, a pin roller thrust bearing (2 of) fits inwards of each thick
washer,(one each end) with a thin thrust washer going in the middle
of the 2 pin roller bearings. (middle of stack)  The bearing stack
has a thick thrust washer-- a pin roller bearing -- the thin center
thrust washer -- another pin roller bearing and then another thick
thrust washer.


The bearing stack slides onto the back of the input shaft. The
bearing stack sits directly onto the Tracy plate and  the rear thick
washer should not turn at all.  Each thick thrust washer at each end
of the bearing stack should not turn.  The rear washer is stationery
on the mounting plate and the front washer turns with the input
shaft. The turning is done by the 2 pin rollers and thin
intermediate thrust washer only.  You say there is wear on the
mounting plate--- Make sure that the rear most thick washer is not
binding on the input shaft.  It must be free to turn without binding
on the input shaft under any circumstances.


Clearance is checked by standing the PSRU on the prop shaft
vertically, removed from the mounting plate.  It may be best to
remove the thick rubber O ring that holds the ring gear of the
planetry in place while you do this as the 2 halves of the PSRU must
be in full contact with each other to not give a wrong clearance
reading. 2 clamps will do the same thing just so long as there is
nil gap between the 2 halves.


Remove the input shaft and bearing stack.  Drop the nylon snubber
washer over the prop shaft that protrudes from the planetry
assembly. Then drop the input shaft down so that the protruding prop
shaft is inserted inside the gear (brass bush inside)  and resting
firmly on the nylon "snubber" washer.  (this is the one and only
nylon washer). Place the bearing stack over the end of the input
shaft and they should just clear a straight edge put across the PSRU
housing that is to bolt onto the mounting plate.


I work on a min of 5 thou, but is not that critical, just so long as
there is clearance. If the bearing stack is proud of the housing,
the nylon washer is to be thinned down, or replaced with a thinner
one until the bearing stack is clear of the afore mentioned straight
edge.  (I use a steel ruler as it is not all that critical, just has
to clear)


Under load the input shaft rests on the bearing stack due to the
helical cut of the gears, (rearward force).  Pull the power so that
the prop now drives the PSRU and the gears (helical) will pull the
input shaft forwards.  The nylon snubber washer takes up any forward
thrust pressure preventing metal to metal contact. Probably clear as
mud??  Ask me for clarification where necessary.

Neil Unger

Hi Neil, How exactly are you stopping the outer planet ring from
turning. Also what do you think the torque load is that makes the
ring gear want to rotate, is it big or reasonably small. Cheers

Chris Hoskins in NZ

Chris, I am talking Tracy Crook's PSRU.  It is mounted on the sprag
gear that comes with the planetry combination. Tracy holds the sprag
gear in place with 6 x 1/4 inch screws. These are prone to come loose
and shear off.

In my PSRU the ring gear is held in the rear section of the alloy
housing with a close tolerance fit. loctited, and held with extended
point screws that are drilled into the ring gear.   The torque
turning load I feel is reasonable great as it has to stop the
Planetry from turning the ring gear.  We have 250 HP attempting to
turn everything or a torque of 300 FT pounds if I remember correctly.
This will lessen as the diameter increases.  My extended point screws
are at the outer of the ring gear which gives the maximum leverage
available.  So far so good at approaching 50 hours.

Neil Unger  the OZ peasant.

Yeah sure :-)

Paul Lamar

Thanks Neil, How did you drill the holes ? I tried with a carbide
tipped drill and it wouldn't even look at it, maybe I needed to use
more force huh. How would get the ring gear out if necessary ?

Cheers
Chris Hoskins NZ


It does take a lot of pressure. Here is a picture I just did. 1/4
inch hole.

BTW on the sun gear you do not need extended point set screws. Just
use short rods and just tig weld them in. Saves taping hard steel.

Paul Lamar


       Chris,     Thankfully I did not have to do it.  The CNC mob
that did the work drilled them.  He did make the comment that they go
through $22,000 a month in cutting tips.  To remove the ring gear if
necessary, my base that holds the ring gear is basically a cylinder that
only holds the ring gear and the ring gear is slightly exposed  at the
back,---- so the screws are removed.  the base heated to destroy the
loctite, then the ring gear can be pressed lightly out of the base.
Each end of the base cylinder has a small O ring groove just inside of
the 12 bolt holes to make the oil seal between the 2 halves and onto the
base plate.  Makes removal and dismantling simple.  NO RTV required.

Cheers,  Neil Unger.

Glad to find locktite works. That is one of the great things about NC machines.
They are super accurate. Usually a little flex (RTV)  is allowed on the ring gear
so it can self center on the planet carrier.

Even the P&W PT 6 planet gear box the ring gear is flexible.

Is your housing multi piece Neal ?. Normally there are no joints
between housing sections that need o-rings.

How about some pictures Neal? It will help me sell your gear boxes.

Paul Lamar

------------------------------------------------------------------
Please  add your questions or comments  at the end of the thread. Not
the beginning.

I am going to enforce that rule. If people don't do that it will not
be forwarded. My ISP changed the rules.

The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.