Subject: New you tube video on the time to climb. 12 c
From: paul lamar
Date: 3/2/2018, 11:15 PM
To: A10-Me-Earthlink


     12 c

    One of the guys at Santa Paula edited one of the videos from the
     cockpit camera and and shot the take off and landing of a test flight
     while I was away. Good job of editing.

     https://www.youtube.com/watch?v=Xe1lwc3fxfs

     Paul Lamar Paul, Can see the oil spraying on the wind shield, but not
     badly. Why continue to dive in that condition?

    Pannic?  Neil Unger

    That may be the time Dan left the gear box oil drain loose and it came out around
    10,000 feet :-) I was not there.


    This poor airplane as been abused :-)

    Just shows to go you how robust this engine and gear box are.

    We failed the last transistor in the Motec 800 so we are going to fly it next
    with out water injection. Some local drag racers told us we don't need water injection
    as the alcohol injection will do the job of cooling the intake charge. That will save up
    to 30 pounds as we can take off with out water in the water tank.

    We had one flight where the intake charge go to 300 f and that did not seem to hurt
    the engine.

    Paul Lamar


       That was very impressive although I think the rate of descendt  was equally impressive. No cowl and that big prop must really slow you down, our Rv6 would have wrapped the air speed indicator around and still would have taken 3 times as long to descend. I had a question about what gauges are on the motec screen, if I am reading it correctly is it only running 15 psi of boost if so that's even more impressive  I would like to know which gauges are what if you don't mind. Congrats and when do you guys plan on going for the official record?

Thank you,

Jacob Sturges


The Motec instrumental panel we have sucks. The numbers are not labeled. No telling what they
are.

Here is what we get out after the flight from the data recording system.

This was a Jan 18th flight. Max manifold pressure was 70 inches of Hg.
It is set to that by the intake manifold  blow off valve.
The throttle vibrated off to 80%.
 RPM was 7954.


The manifold pressure is limited by the blow off valve because the prop is limited.
As it is now the prop tips are near Mach 1

If we had wider blades we could
up the blow off valve to 85 inches HG which of coarse is 21% more HP.

So my guess we are only getting about 520 HP. We had 650 HP on the dyno.

We have had it up to 85 inches of HG but the RPM or the thrust did not increase.
So 70 inches HG is all we need to get max thrust out of this prop.

With the right wider blade  prop we should do the climb in one minute 36 seconds.
Right now the best we have seen is one minute 47 seconds.
A new prop would cost $5000 and take 3 months to build. We are not going to do it.

BTW I am sure Felix Wankel had no idea his engine was this robust :-)

P&W Canada are shaking in their boots. Deathly afraid some one will build
a turbo Wankel to compete with the PT6 at half the cost and twice the altitude.

So they are trying to build a patent mine field around the Wankel :-)

We plan on flying it again on Monday.

Paul Lamar

------------------------------------------------------------------

     Please  add your questions or comments  at the end of the thread. Not
     the beginning.

     I am going to enforce that rule. If people don't do that it will not
      be forwarded. My ISP changed the rules.

     The Rotary Engine free News Letter. Powered by Linux. If you want
     off the list PLEASE let me know and I will remove  you.  ACRE NL web
     site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
     Copyright 1998-2018 All world wide rights reserved.