Subject: blow down turbine calculations 12 a
From: paul lamar
Date: 12/27/2018, 1:57 PM
To: A10-Me-Earthlink





 12  a
 
 
   So Paul,
 which style of turbine do you think would give the best
 efficiency in a
 single stage blown, direct
 coupled application. Short and deep, or tall and shallow.
 
 C. Smith
 
 Assume for the moment the exhaust gas velocity
 is 200 MPH  at 1000 RPM.
 Wide open
 throttle.  Full power it would be 700 MPH.
 
 Dynamic pressure in pounds per
 square foot is MPH squared times .0026 constant
 so the pressure  on the blades   is 200 X 200
 X .0026 = 104  pounds per square foot.
 
 
 At 1000 RPM If the turbine is
 18 inches in diameter
 or a foot and a half
 in diameter the circumference is 4.71 feet The blade
 velocity is
 there fore
 471
 feet per minute or 5.3 MPH
 
 If the blade is 2 inches long and one inch
 wide
 the area is 2 square inches or 2/144
 = .0138 square feet.
 One blade is only .0138
 square feet
 The total area for all 47 of the
 blades is .6486 square feet.
 
 This assumes the lift coefficient of the blade
 is one
 The lift coefficient is a function of
 the blade angle relative
 to gas flow
 direction. Ideally it would change with RPM.
 
 47 X  .0138 or .648 square
 feet total.
 So the pressure is 104 pounds
 per square foot.
 104 X .648 or  67.4 pounds
 total.
 
 The blade radius is
 9 inches or .75 feet.
 
 The
 total torque at 1000 RPM or roughly idle RPM wide open
 throttle
 is 67.4  pounds times .75 feet
 radius or roughly  50.5 foot pounds of torque
 on the E shaft. This assumes wide open throttle
 at 1000 RPM.
 
 As the RPM
 goes up the blade keeps going faster and the exhaust gas
 velocity increases.
 And the pressure on the
 blade is adjusted because the
 velocity of
 the blade is subtracted from the exhaust gas velocity.
 
 However the velocity of the
 gas increases to super sonic or
 about 700  MPH at high RPM.
 
 At 8000
 RPM the gas velocity relative to the blade is only 428  MPH.
 
 471 x 8000 RPM =  37680  divided by 88 is 428 MPH
 
 Dynamic pressure in pounds per square foot is
 MPH squared times .0026 constant.
 
 The pressure on the blade is 428 MPH x 428 MPH
 X .0026 or  476 pounds per square feet.
 
 If the blade is 2 inches long
 and one inch wide
 the area is 2 square
 inches or 2/144 .0138 square feet.
 One blade
 is only .0138 square feet
 so the force on
 just one blade is 6.57 pounds     total
 tangential force times is  47 blades or 308 pounds.
 torque arm is only .75 feet (disk blade radius)
 so torque is only 231 foot pounds.
 
 HP = torque X  RPM / 5252 so the added HP at
 8000 RPM is  only 231 HP.
 
 This is typical for a one to one turbine.
 
 Here is a plot of the
 situation.
 
 
 A smaller turbine would help the aircraft
 application.
 The velocity of the blade would
 be slower so the pressure
 would be
 higher.
 
 18 inches would be
 fine for a car but an AC engine might need a geared
 turbine.
 
 Check my logic and  arithmetic. I have been
known to make mistakes.
 
 Paul Lamar
 
Thanks for the info Paul. I don't have the resources for another gearbox. Will be sticking with your original concept illustration.
It will be leaky and crude, but it's as much as I can do. Still looking to find someone who can cut down an E-shaft for a single rotor.

I'm limited in RPM due to the RD1C gearbox. I have committed to the first turbine on eBay, as it closely matches your rendering.
I will get the rest of the measurements when it arrives.

Craig Smith


Mounting it on the back would be easier.

Paul Lamar

------------------------------------------------------------------
Please  add your questions or comments  at the end of the thread.
Not the beginning.

I am going to enforce that rule. If people don't do that it will not be published.
My ISP changed the rules.

The Rotary Engine free News Letter. 750 subscribers world wide.
Powered by Linux. If you want off the list PLEASE let me know and I will remove  you.

ACRE NL web site. http://www.rotaryeng.net
YouTube  Key word "PaulLamar2". Keep clicking
this as Youtube will try to divert you to advertising.
Copyright 1998-2018 All world wide rights reserved.