12 a
So Paul,
which style of turbine do you think would give the best
efficiency in a
single stage blown, direct
coupled application. Short and deep, or tall and shallow.
C. Smith
Assume for the moment the exhaust gas velocity
is 200 MPH at 1000 RPM.
Wide open
throttle. Full power it would be 700 MPH.
Dynamic pressure in pounds per
square foot is MPH squared times .0026 constant
so the pressure on the blades is 200 X 200
X .0026 = 104 pounds per square foot.
At 1000 RPM If the turbine is
18 inches in diameter
or a foot and a half
in diameter the circumference is 4.71 feet The blade
velocity is
there fore
471
feet per minute or 5.3 MPH
If the blade is 2 inches long and one inch
wide
the area is 2 square inches or 2/144
= .0138 square feet.
One blade is only .0138
square feet
The total area for all 47 of the
blades is .6486 square feet.
This assumes the lift coefficient of the blade
is one
The lift coefficient is a function of
the blade angle relative
to gas flow
direction. Ideally it would change with RPM.
47 X .0138 or .648 square
feet total.
So the pressure is 104 pounds
per square foot.
104 X .648 or 67.4 pounds
total.
The blade radius is
9 inches or .75 feet.
The
total torque at 1000 RPM or roughly idle RPM wide open
throttle
is 67.4 pounds times .75 feet
radius or roughly 50.5 foot pounds of torque
on the E shaft. This assumes wide open throttle
at 1000 RPM.
As the RPM
goes up the blade keeps going faster and the exhaust gas
velocity increases.
And the pressure on the
blade is adjusted because the
velocity of
the blade is subtracted from the exhaust gas velocity.
However the velocity of the
gas increases to super sonic or
about 700 MPH at high RPM.
At 8000
RPM the gas velocity relative to the blade is only 428 MPH.
471 x 8000 RPM = 37680 divided by 88 is 428 MPH
Dynamic pressure in pounds per square foot is
MPH squared times .0026 constant.
The pressure on the blade is 428 MPH x 428 MPH
X .0026 or 476 pounds per square feet.
If the blade is 2 inches long
and one inch wide
the area is 2 square
inches or 2/144 .0138 square feet.
One blade
is only .0138 square feet
so the force on
just one blade is 6.57 pounds total
tangential force times is 47 blades or 308 pounds.
torque arm is only .75 feet (disk blade radius)
so torque is only 231 foot pounds.
HP = torque X RPM / 5252 so the added HP at
8000 RPM is only 231 HP.
This is typical for a one to one turbine.
Here is a plot of the
situation.
A smaller turbine would help the aircraft
application.
The velocity of the blade would
be slower so the pressure
would be
higher.
18 inches would be
fine for a car but an AC engine might need a geared
turbine.
Check my logic and arithmetic. I have been
known to make mistakes.
Paul Lamar
Thanks for the info Paul. I don't have the resources for another gearbox. Will be
sticking with your original concept illustration.
It will be leaky and crude, but it's as much as I can do. Still looking to find
someone who can cut down an E-shaft for a single rotor.
I'm limited in RPM due to the RD1C gearbox. I have committed to the first turbine on
eBay, as it closely matches your rendering.
I will get the rest of the measurements when it arrives.
Craig Smith
Mounting it on the back would be easier.
Paul Lamar
Craig,
Might I suggest, If you have a community college near you with a machine shop
program, you contact the instructor, and explain what you need. He could give you the
name of some of the best students. Ask the student to do a "special project", and
slip a few bucks too cut the E-shaft. Everybody is a winner.
Good luck with the project, and keep updates coming.
Norm Parmley
------------------------------------------------------------------
Please add your questions or comments at the end of the thread.
Not the beginning.
I am going to enforce that rule. If people don't do that it will not be published.
My ISP changed the rules.
The Rotary Engine free News Letter. 750 subscribers world wide.
Powered by Linux. If you want off the list PLEASE let me know and I will remove you.
ACRE NL web site.
http://www.rotaryeng.net
YouTube Key word "PaulLamar2". Keep clicking
this as Youtube will try to divert you to advertising.
Copyright 1998-2018 All world wide rights reserved.