> Perhaps what is also happening is silicon nitride ceramic roller
> rotor bearings and
> silicon nitride ceramic apex seals are being used so it is less
> important to cool
> the rotors. Ceramic roller bearings are less affected by high heat
> than steel
> bearings. Same goes for apex seals. Some of the reasons for oil
> cooling the rotors
> in the Mazda is to cool the rotor bearings and help cool the apex
> seals. Most of
> the apex seal cooling is now done by the injected apex seal oil in
> the Mazda engine.
>
> With less rotor cooling there is less waste cooling heat.
>
> Paul Lamar ...No rotor no motor.
>
> Paul,
> Since the Mazda uses plain bearings anyway it would seem oil cooling
> would be more of a natural solution. The first company that ever did the
> pass-thru charge cooling, (to my knowledge anyway), was BSA. They had a
> full road going prototype motorcycle shortly before going bankrupt. Some
> people say that was the basis for the Norton rotary, others tell me that
> it was an independent effort. Mazda was impressed enough with the BSA
> effort to buy several of the new patents they filed. I often wondered if
> a blended variant might work well. The idea would be to use air cooling
> for the rotor, with the standard water for the housings. The rotors
> could be considerably lighter that way. Just thinking out loud.
> Bill Jepson
>
> The Norton and Midwest, now Diamond, engines use air cooling.
> It is not free however as it take HP to drive the required
> air pump.
>
> Paul Lamar ...No rotor no motor.
>
> Paul,
> Something of interest on the BSA engine was that it didn't use a fan.
> The engine used carbs which were drawn through first. The charge then
> went between the rotors (2 rotor) and was drawn through the rotor tips
> only by the induction vacuum. Then the charge was put into the
> combustion chamber thru a P-port. Kind of a over, under, around and
> through thing. Very unique at that time. They said preheating the charge
> helped mileage, but that might have been hype.
> Bill Jepson
>
> -------------------------------------------------------------
>
> As the second licensee (after Curtiss Wright) Sachs in
> Schweinfurt/Germany began producing the 294 cc (which is 18 cu in)
> rotary with charged-cooled rotor for several purposes in the Mid-1960s.
> They sold a big quantity of those engines to USA and Canada for snow
> mobiles. This snow mobile engine was the basis for the DKW and the early
> BSA motorcycles. BSA switched over to Twin-Rotor 2 x 294 cc immediately.
> With the crisis of the english motorcycle industry nearly all the
> english companies came under one roof. So the early BSAs and later
> Nortons are all the same. They have the gas flow through this big plenum
> chamber in the motorcycle frame as described. The best time for Norton
> rotaries was 1985..1995, when they build police-, sports- and touring
> bikes. They were also very succesful in british motorcycle racing
> (versus high tuned Japanese bikes) ? but had no money to compete in
> international events. A very good overview of the early development is
> in SAE paper 821068.
>
> After Sachs stopped the rotary story in 1977 all the tooling machines
> and the stuff went to Norton and a lot of the parts for 294 cc units
> worldwide were produced at Norton. Two companies were splitted off from
> Norton: UAV with engines for unmanned and military aircrafts and Mid
> West (later Diamond) for commercial aircrafts. UAV pushed the 1-rotor up
> to 60 HP! At a technical meeting such an engine found place in the bag
> of its developer without a problem.
>
> The Mid West engines have p-ports and a big fan for cooling the rotor
> with fresh air. This improves cooling a lot, but gives the problem of
> throwing out residuals of oil with that cooling air. In Karts always
> running on the same short track this wasn´t a possible solution. So the
> Aixro engines (made by Rothkranz) have that combined p-port/side port.
> But it is said, that the engine should not run on the p-port for more
> than 30 seconds ? no problem in Kart racing.
>
> The story of that charge cooled 294 cc rotaries began in 1965 and isn´t
> finished yet!
>
> Reiner and the motorcycle Guys from Germany
>
> Reiner,
>
>
> I am very happy to hear from someone who has some info on the rotary BSA
> and later Norton.
> Most times when I mention it people look at me like I have two heads or
> something! I didn't
> know of the Sachs heritage. I do recall considerable interest in the
> machines just before BSA
> bit the dust. I loved the all monocoque chassis Norton tried on both
> rotary and piston engine
> bikes of that era. That chassis probably spawned all the later twin-spar
> frames on the
> Japanese bikes.
> Bill Jepson
Here is the family tree of the Fichtel & Sachs KM914 and the derivitives. If
anyone knows of any other branches, let me know and I'll update it.
http://www.wankel.org/Diamond/Sachs_Family_tree.txt
Mark Wrathall
Mark, Bill,
some years ago we made a poster of the family tree of motorcycles with
rotary engine (it is not really complete). On the left side are all the
motorcycles rooting on the Sachs KM 914. In the first BSA and Hercules
prototypes you can make out the KM 914 very clearly. But it must be said
that only the geometrical data and the displacement remained. The design
of the parts, the gas flow, the cooling and lots of other things were
developed dramaticly ? of course also in the aircraft engines.
But anyway, this 294 cc (18cu.in.) is a main connecting thread through
40 years of small Wankel engines. The first version of the KM 914 had
303 cc displacement. For whatever reason they changed it to that 294 cc
in the second version by just reducing the rotor width.
As far as I know OMC had completely their own development of charge
cooled rotaries ? nothing to do with Sachs. Same as Yanmar in Japan.
The KM 914 was in the early Arctic Cat snowmobiles. At that time Sachs
people have been very often in Thief River Falls/Minnessota (home of
Artic Cat) and experienced some interesting and funny things. For
example: How do snowmobile people measure the torque of an engine? Just
by measuring the height of the snow pile behind the vehicle after full
accelerating.
In the 1970s there must have been small formula racing cars (for hiring
by everybody) on lots of racetracks in US. They were also powered by the
KM 914.
As it also powered generators, waterpumps, hydraulicpumps,
earthdrill-mashines and lots more this was really a multi-purpose-engine.
Reiner Nikulski
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.